Hello everyone, today the editor has paid attention to a more interesting topic, which is about the steps and methods of making network cables, so the editor has sorted out 2 related answers to introduce the steps and methods of making network cables , let's take a look. How to make network cable? Network cable production process sharing? How to make network cable? The steps of making the network cable: 1. Cutting. Use the cutting edge of the wire crimping pliers to cut the appropriate length of the network cable. 2. Peeling. Use the cutting edge of the wire crimping pliers to cut the thread ends evenly, and then put the thread ends into the stripping knife edge, let the corner of the thread end and the baffle, hold the crimping pliers slightly and rotate slowly, let the knife edge cut the protective rubber of the twisted pair, Pull off the rubber. 3. Sort. After peeling off the outer sheath, you can see 4 pairs of 8 core wires of the twisted pair network cable, and you can see that the colors of each pair are different. Each pair of wires is intertwined with each other. When making a network cable, the 8 thin wires of the 4 wire pairs must be disassembled one by one, straightened out, straightened, and then arranged neatly according to the specified wire sequence. 4. Cut neatly. Straighten the wires as far as possible (do not twist), flatten (do not overlap), squeeze and straighten (close to one direction), and then use crimping pliers to cut the wire ends evenly. In this way, after the twisted-pair wires are inserted into the crystal head, each wire can be in good contact with the pins in the crystal head to avoid poor contact. 5. Insert. Hold the crystal head with your thumb and middle finger, so that the side with the plastic shrapnel faces down, and the pin side faces away from you, and use your index finger to hold it; hold the rubber outside the twisted pair with the other hand, and slowly and firmly connect the 8 wires. At the same time, insert along the 8 wire slots in the RJ-45 head, and insert it to the top of the wire slot. 6. Repression. After confirming that all the wires are in place, and checking the line order through the crystal head, you can clamp the RJ-45 head with the crimping wire. After pushing the RJ-45 head from the toothless side into the clamping groove of the wire crimping pliers, hold the wire pliers firmly (if your strength is not strong enough, you can use both hands to press together), press all the protruding pins into the crystal And head inside. Reminder: 568B - Arrange each color line group from left to right in the following order: white orange, orange, white green, blue, white blue, green, white brown, brown. 568A - From left to right: white/green, green, white/orange, blue, white/blue, orange, white/brown, brown. Network cable production process sharing? Step 1: We first use the cutting edge of the wire crimping pliers to cut out the length of the twisted pair that we plan to use. Step 2: We need to peel off the gray protective layer of the twisted pair. You can use the cutting edge of the wire crimping pliers to trim the ends of the wires. Rotate slowly so that the knife edge cuts through the protective rubber of the twisted pair. The method of straightening the cable is also very simple, use both hands to hold the cable. Then apply force in two opposite directions and pull up and down. Step 3: After we arrange the cables in order and straighten them, we should check them carefully, and then cut the top of the cables neatly with the cutting edge of the wire crimping pliers. It should be noted that the cutting should be in a horizontal direction Insert it, otherwise the different length of the cable will affect the normal contact between the cable and the crystal head. Step 4: After cutting, you should try to press the cables as tightly as possible, and you should avoid moving or bending the network cables a lot, otherwise it may cause unevenness in several groups of cables that have been arranged and cut. Step 5: All we need to do is to insert the organized cables into the crystal head. It should be noted that the side of the crystal head with the molded material spring is facing downward, and the side with the stitches is upward, so that the end with the stitches points away from you, and the end with the square hole faces you. At this time, the leftmost is the first foot, the rightmost is the eighth foot, and the rest are arranged in order. When inserting, pay attention to inserting 8 cables slowly and forcefully along the 8 wire slots in the RJ-45 head at the same time, and insert them to the top of the wire slots. Step 6: Before the last part of the crimping line, we can check from the top of the crystal head to see if each set of cables is tightly pressed against the end of the crystal head. Step 7: Of course, it is crimping. After confirming that it is correct, you can insert the crystal head into the 8P slot of the crimping pliers to crimp the wire. After inserting the crystal head, hold the wire pliers firmly. If you are not strong enough, you can use both hands Press together, such a pressing process makes the protruding pins of the crystal head all press into the crystal head, and you can hear a slight "pop" after the force is applied. Step 8: After crimping, all the protruding pins of the crystal head are pressed into the crystal head, and the plastic buckle at the bottom of the crystal head is also pressed tightly on the gray protective layer of the network cable. At this point, the above is the introduction of the editor to the steps and methods of making network cables. I hope that the two-point answer about the steps and methods of making network cables will be useful to everyone.